IP address of the SIP server: 200.200.200.200/24. If the existing DBA profiles in the system do not meet the requirements, run the dbaprofile add command to add a DBA profile. - TR069 is based on the IP protocol and requires an extra IP management network. In this example, the default digitmap profile, namely digitmap-profile_1 is used. Run the ont add command to add an ONU. Configure the IP address of the PC network adapter to be in the same network segment with the IP address of the local maintenance Ethernet port on the ONU (default: 192.168.100.1). For ONU, set the MG ID to 1, apply SIP agent profile 2 to ONU, and use default values for other parameters. a. Configure the IP address of the PC network adapter to be in the same network segment with the IP address of the local maintenance Ethernet port on the ONT. In this example, the default POTS port profile, namely POTS port profile 1 is used. Run the sippstnuser codec command to configure the SIP user codec. (Optional) Bind the alarm profile to ONU 1. Bind the two ONTs to ONT line profile ftth and ONT service profile ftth.There are two methods of adding an ONT: add an ONT offline and confirm an automatically discovered ONT.Add ONTs offline.If the password of an ONT is known, run the ont add command to add an ONT offline. Run state : online //Indicates that the ONU goes online successfully. Select either mode as required. Services can be configured for This solution allows the U2000 to manage the OLT using SNMP, manage voice and Layer 3 services using TR069, and manage PON link layer using OMCI. Therefore, the ARP proxy function needs to be enabled on the OLT. for the default alarm profile are 0, which indicates that no alarm After the configurations are complete, run thecommitcommand to apply the parameters settings. Data planning Table 4-7 Data planning Item Data Traffic profile l profile name: traffic_table_videomonitor l CIR: off l priority: 5 ONU line profile Profile name: pol_line_all GEM port ID: 16 Networking data Uplink port: 0/2/0 PON access port: 0/1/0 ONU ID: 3 VLAN Planning Single VLAN tag l S-VLAN ID: 200 l C-VLAN ID: 200 l VLAN type: smart l VLAN attribute: common Issue 02 (2018-10-10) Copyright Huawei Technologies Co., Ltd. 70 Agile POL Solution Configuration Guide 4 Campus Configuration Guide Procedure Step 1 Configure a traffic profile. You need to log in to comment to the post, Third Partys Trade Secret refers to Third Partys (other than Huaweis) technical or commercial information which is unknown to the public, with commercial value, and kept confidential by Third Party. Connect two ONTs to GPON port 0/1/0. is generated. Contact us About This Chapter, Views 1,375 huawei(config-gpon-srvprofile-1)#quit Step 2 Add an ONU. Then, the ONU automatically recovers of the PON port. Create a GPON ONT line profile, named ftth, and bind it to the DBA profile. Configure the capability set of the ETH port and POTS port toadaptive. Create the maximum PoE class of an ONT Ethernet port class 3. huawei(config)#interface gpon 0/1 huawei(config-if-gpon-0/1)#ont port poe 0 3 eth 1 enable max-power-class class3 huawei(config-if-gpon-0/1)#quit NOTE To check whether a device supports PoE, see the corresponding product documentation. The webpage login supports SSL3.0, TLS1.0, and TLS1.1. In the login window, enter the user name (default: telecomadmin) and password (default: admintelecom) of the administrator. profile 1 is used in this example. or SN of an ONT is unknown, run the port portid ont-auto-find command in GPON mode to enable the ONT auto-discovery function of Run the display ont-sipagent-profile command to query the existing SIP agent profile in the system. b. Note that the sum of the fixed bandwidth and the assured bandwidth must not be greater than the total bandwidth of the PON port. Configure the IP huawei(config)#interface gpon 0/1 huawei(config-if-gpon-0/1)#ont add 0 1 sn-auth 3230313126595540 omci ontsrvprofile-name pol_ser ont-lineprofile-name pol_line_all l Confirm automatically discovered ONUs huawei(config)#interface gpon 0/1 huawei(config-if-gpon-0/1)#port 0 ont-auto-find enable //Enable the ONT auto-find function of a gpon port. - An OLT version and an ONT version are not bound to each other. 4.3 Configuration Procedure This section describes the services configuration procedure for the Agile POL solution in the campus. Related configurations can be performed for ONUs only after the ONUs are successfully added to OLT-A. ont-lineprofile add Add a service profile. types, in which. Data Planning Table 4-1 Data Planning ON U ID Servi ce Type PO N Port GEM Port ID TCO NT SVL AN CVL AN DBA Profile ONU Line Profile l Profile name: pol_dba_hsi Data/ HSI 13 2 100 100 l Type: Type4 l Maximum bandwidth: 100 Mbit/s l Profile name: pol_dba_voip l Type: Type3 1 VoIP (SIPBased) 0/1/0 12 3 300 300 l Assured bandwidth: 1 Mbit/s pol_line_all l Maximum bandwidth: 10 Mbit/s l Profile name: pol_dba_wifi Wi-Fi 18 7 1001 1001 l Type: Type4 l Maximum bandwidth: 100 Mbit/s l Profile name: pol_dba_ap 2 Issue 02 (2018-10-10) AP 0/1/0 15 4 400 400 Copyright Huawei Technologies Co., Ltd. l Type: Type4 l Maximum bandwidth: 100 Mbit/s pol_line_all 52 Agile POL Solution Configuration Guide 4 Campus Configuration Guide ON U ID Servi ce Type PO N Port GEM Port ID TCO NT SVL AN CVL AN DBA Profile ONU Line Profile l Profile name: pol_dba_hsi Data/ HSI 13 2 100 100 l Type: Type4 l Maximum bandwidth: 100 Mbit/s l Profile name: pol_dba_video monitor Camer a Acces s 16 5 200 200 l Type: Type4 l Maximum bandwidth: 100Mbit/s l Profile name: pol_dba_ap AP 3 15 4 400 400 0/1/0 Camer a Acces s l Type: Type4 l Maximum bandwidth: 100 Mbit/s l Profile name: pol_dba_video monitor 16 5 200 200 pol_line_all l Type: Type4 l Maximum bandwidth: 100Mbit/s 4.3 Configuration Procedure This section describes the services configuration procedure for the Agile POL solution in the campus. Configure the Wi-Fi parameters. TR069 provides an enhanced definition and deployment scenario for the IP based customer premises equipment (CPE) service management model. For ONU, configure the IP address obtaining mode to the DHCP mode, set the management VLAN to VLAN 300, and use default values for other parameters. A T-CONT is bound to a DBA profile for dynamic bandwidth allocation, improving upstream bandwidth utilization. If you can remotely log in to the ONU from the OLT to perform configurations for the ONU, the management service port between the OLT and the ONU is available. Confirm automatically discovered ONTs.If the password or SN of an ONT is unknown, run the port portid ont-auto-find command in GPON mode to enable the ONT auto-discovery function of the GPON port. the configuration of the alarm profile is not required.

Profile type: fixed bandwidth and minimum delay mode, DBA bandwidth: 28928 kbit/s (assume that 4 E1 private lines are connected to 1 ONU and each E1 private line is configured with a bandwidth of 7232 kbit/s). Issue 02 (2018-10-10) Copyright Huawei Technologies Co., Ltd. 50 Agile POL Solution Configuration Guide 4 Campus Configuration Guide 4.1 Campus Usage Scenario This chapter introduces the usage scenario of AgilePOL solution in campus. Both the ONU password and SN are not obtained. 4.9 Configuring the Camera Access Service The OLT is connected to the remote ONU through a GPON port, ONU is connected to the camera through a ethernet port, camera provide user with video monitor service. Copyright Huawei Technologies Co., Ltd. 63 Agile POL Solution Configuration Guide 4 Campus Configuration Guide Run the pstnport electric command to apply a POTS port profile to an SIP interface or configure the interface customized parameters, or run the ont-pstnport electric batapply command to bulk apply the POTS port profiles to SIP interfaces. DBA profiles in the system. Query a DBA profile. If you use these two commands to apply the SIP service data profiles or configure the interface customized parameters repeatedly, the last configurations take effect. huawei(config-gpon-lineprofile-1)#gem add 12 eth tcont 3 //Bind the Data/HSI service GEM Port 12 to ONU line profile. l The Web page for configuring ONT varies with ONT versions, but the parameter configuration is the same. If multiple ONTs of the same type bound to the same line profile or service profile are connected to the same port, you can bulk add ONTs by bulk confirming automatically discovered ONTs to make configuration easier and more efficient. Issue 02 (2018-10-10) Log in to the Web configuration page. huawei(config)#dba-profile add profile-name pol_dba_voip type4 max 102400 Issue 02 (2018-10-10) Copyright Huawei Technologies Co., Ltd. 55 Agile POL Solution Configuration Guide 4 Campus Configuration Guide Set the WiFi service profile name to pol_dba_wifi, profile type to type4, maximum bandwidth to 100 Mbit/s. Set the profile name to traffic_table_videomonitor, the CIR to off, and the priority to 5. The user information includes operations, 8 Ensure that Config flag of the ONU is active, Run State is online, Config state is normal, and Match state is match. Based on SNMP and TR069, this solution allows the ACS to manage home terminals in a unified manner, reducing O&M costs. Configure the inband management VLAN and IP address of the ONU. configure all the layer properties on these modems. Run the display ont-mg-attribute-profile command to query the existing interface common profile in the system. Configure a POTS port profile. Address: Copyright 2022 PDFCOFFEE.COM. 2. A maximum of 100 products can be subscribed. [emailprotected] To add sub digitmap scheme [xABCD].S|[xABCD].# to the digitmap profile named digitmap-profile_1, do as follows: huawei(config)#ont-digitmap-profile token add profile-name digitmapprofile_1 dial-plan-token [xABCD].S|[xABCD].# Step 6 Configure an IP address for an ONU SIP user. 4.1 Campus Usage Scenario This chapter introduces the usage scenario of AgilePOL solution in campus. PoE cannot be implemented on a device that does not support it. Then, restart the browser. huawei(config)#service-port vlan 200 gpon 0/1/0 ont 3 gemport 16 multi-service user-vlan 200 tag-transform translate inbound traffic-table name traffic_table_videomonitor outbound traffic-table name traffic_table_videomonitor Step 7 (Option) Configure the power over Ethernet (PoE) function for an ONU Ethernet port. Configure the in-band management service port. The OLT does not limit the rate of inband management services. Access Network Operation Divisi Service Ope, | =================================================================================== ============================= 1) A, Name In the right pane, configure parameters of the SIP-based voice interface as follows (other parameters use the default settings): The parameters of the SIP-based voice interface must be consistent with the corresponding configuration on the softswitch.

ONU and save the modification. 6.The ACS encapsulates user information in a TR069-compliant format and sends it to Issue 02 (2018-10-10) Copyright Huawei Technologies Co., Ltd. 53 Agile POL Solution Configuration Guide 4 Campus Configuration Guide 4.4 Adding an ONU to an OLT Services can be configured for an ONU only after the ONU is successfully added to an OLT. Configure a DBA profile.Run the display dba-profile command to query the existing DBA profiles in the system.

Issue 02 (2018-10-10) Copyright Huawei Technologies Co., Ltd. 54 Agile POL Solution Configuration Guide 4 Campus Configuration Guide Table 4-2 Introduction to ONU profiles Profile Type Function Command DBA profile DBA profile describes GPON traffic parameters. In the right pane, User Status is Up. A T-CONT is bound to a DBA profile for dynamic bandwidth allocation, actual capability of the online ONT. Agile POL Solution Configuration Guide There are two methods of adding an ONT: add an ONT offline After the configurations are complete, run the commit command to apply the parameters setting. huawei(config)#dba-profile add profile-name pol_dba_hsi type4 max 102400 Set the VoIP service (SIP-based) profile name to pol_dba_voip, profile type to type4, maximum bandwidth to 100 Mbit/s. Configure a digitmap profile. Set the Data/HSI service profile name to pol_dba_hsi, profile type to type4, maximum bandwidth to 100 Mbit/s. If the existing SIP service data profile in the system does not meet the requirements, run the ont-siprightflag-profile add command to add an SIP service data profile. S2750&S5700&S6700 V200R005(C00&C01&C02&C03) , S2750&S5700&S6700 V200R003(C00&C02&C10) . Then the IP channel is set up. l Digitmap profile: saves the digitmap information about an ONU, including the timeout time of the digitmap timer and the digitmap format. an alarm is reported to the log host and the NMS. Note that the sum of the fixed bandwidth and the assured bandwidth must not be greater than the total bandwidth of the PON port. Report the problem to Huawei technical support website: Download and install the latest HedEx Lite version. Packets are scheduled according to the priority specified in the profile. If parameters in an SIP agent profile are changed, the SIP agent profile must be reapplied to the ONU so that the changed parameters can take effect. The thresholds for all the alarm parameters in the default alarm profile are 0, which indicates that no alarm is generated. To delete sub digitmap scheme 1 from the ONT digitmap profile named digitmapprofile_1, do as follows: huawei(config)#ont-digitmap-profile token del profile-name digitmapprofile_1 dial-plan-id 1 b. huawei(config)#save Step 2 Configure the ONT on the Web page. user count of the ONT. The OLT is connected to the remote ONU through a GPON port to provide users with the SIP-based high-quality and low-cost VoIP service. Run the display dba-profile command to query existing DBA profiles in the system. and confirm an automatically discovered ONT. Run the display traffic table ip command to query existing traffic profiles in the system. l If Run state is offline, a physical line may be broken or the optical module may be damaged. Issue 02 (2018-10-10) Copyright Huawei Technologies Co., Ltd. 64 Agile POL Solution Configuration Guide 4 Campus Configuration Guide Data Plan Table 4-5 Data Plan Item Data Traffic profile WiFi service traffic profile: l profile name: traffic_table_wifi l CIR: off l priority: 0 ONT line profile Profile name: pol_line_all GEM port ID: 18 Networking data Uplink port: 0/2/0 PON access port: 0/1/0 ONU ID: 1 VLAN Planning Single VLAN tag l S-VLAN ID: 1001 l C-VLAN ID: 1001 l VLAN type: smart l VLAN attribute: common NOTE If the Wi-Fi service S-VLAN multiplexing Internet service S-VLAN, then the Wi-Fi service can reuse the Internet service data planning, including VLAN, Gem Port, QoS. 1.The OSS issues service configuration parameters to the U2000 using the TL1 NBI. huawei(config-if-gpon-0/1)#if-sip add 0 1 1 sipagent-profile profile-id 2 Issue 02 (2018-10-10) Copyright Huawei Technologies Co., Ltd. 62 Agile POL Solution Configuration Guide 4 Campus Configuration Guide 2. The OLT can ping the IP address of the SIP server successfully. Management VLAN and management IP address for OLT, In-band management IP address: 192.168.50.1/24, Management VLAN and management IP address for ONU, In-band management IP address for ONU 3: 192.168.50.2/24. huawei(config-gpon-lineprofile-1)#commit huawei(config-gpon-lineprofile-1)#quit 3. For details, see relevant ONT manuals. Create a GPON ONU line profile, named pol_line_all. is 0; when the QoS mode is flow-car or gem-car, traffic profile 6 csw-sajjad-haider-OLT(config)#ont-srvprofile gpon profile-id 11 { |profile, Standard Operation Procedure Open ONT ZTE (ONT F660 and F609) ke OLT Huawei Check the ONT connection status. 1. run the ont add command to add an ONT offline. Check the line and the optical module. Run the display traffic table ip command to query existing traffic profiles in the system. Procedure Step 1 Configure GPON ONU profiles.GPON ONU profiles include the DBA profile, line profile, and service profile. GPON Access for the OLT one Side and E1 or SHDSL access for the OLT on the Peer Side. Configure an ONU line profile. Prerequisites The ONU is added to the OLT. No bulletins found. Create a GPON ONT service profile, named ftth. Select another product to view multimedia documents. Different interfaces are used to manage the ONT. In the navigation tree, choose Status > WAN Information. Packets are scheduled according to the priority specified in the profile. ----End Result SSID radio signals can be searched on the Wi-Fi terminal. mask: 255.255.255.0. How to configure route wan of ont from olt 5608t. Create service flow, set the service VLAN to 100, GEM port ID to 13, and user VLAN to 1001, and use traffic profile traffic_table_hsi. Create a GPON ONU service profile, named pol_ser. Data planning Table 4-3 Data planning Item Data Traffic profile Profile name: traffic_table_hsi CIR: 100M bit/s ONU line profile Profile name: pol_line_all GEM port ID: 13 Networking data Uplink port: 0/2/0 PON access port: 0/1/0 ONU ID: 1 VLAN Planning Single VLAN tag l SVLAN ID: 100 l CVLAN ID: 100 l VLAN type: smart l VLAN attribute: common Procedure Step 1 (Option) Configure a traffic profile. l Add ONUs offline. The default GPON alarm profile 1 is used. Apply an interface common profile. In order to configure the wifi and other layer 3 settings in the modem, you can login to the HG8245H using this IP address: Configure the IP