Don't fill the hinge up with all the screws yet in case it needs adjusting, unless you are hanging a heavy fire check door. Click here for help applying a leading edge, Click here if the door needs adjusting in some way. Sand any remaining pencil lines off. As always, Dash Doors Contract Door & Hardware Group reviews all of these considerations when estimating and detailing your project.

Normally this is into the room (if from a hallway). How to hang a door perfectly was one of the first things I learned to do when I started my carpentry apprenticeship. Slide the hinge up to the line until it covers the x and mark the other end (height) of the hinge.

Decorative tips and conversion kits are available for decorative effects. I use 45mm ovals or 75mm 'Lost-heads' for lightweight/ply flush doors. Finish on hinges can be furnished to Stanley or ANSI/BHMA Standards. This method (not a Stanley knife) ensures the door will always close flush to the frame on the hinge side. Use an electric plane or a circular saw if a lot needs to be removed. YOU AGREE THAT YOU MUST EVALUATE ALL INFORMATION AND RESPONSES, AND THAT YOU BEAR ALL RISKS ASSOCIATED WITH, THE USE OF THIS SITE, INCLUDING ANY RELIANCE ON THE ACCURACY,COMPLETENESS, OR USEFULNESS OF ANY INFORMATION OR MATERIALS MADE AVAILABLE THROUGH THIS SITE.

If you are still struggling use google images to find the type of door so you can see which way up it should go.. First, prepare the door lining or frame. Bang a nail half way in at each line that will keep the door flush with the frame and stop it falling through during marking out. In terms of which way up you should hang your door (sometimes it isn't actually obvious, especially if you are blind), a four or six panelled door generally has a taller horizontal stile across the bottom of the door than at the top.

Refer to the notes section of this solution. If not (and it's not on a drawing), before you can hang the door you need to determine which way the door will swing.

Once there is a screw in the top of the door, it is easier to pivot the door up straight and screw the middle hinge in, then the last one at the bottom. For 1 3/8" doors prepared with3 1/2" (Steelcraft standard hinge backset): INFORMATION PROVIDED THROUGH THIS SITE IS PROVIDED TO YOU AS IS WITHOUT ANY EXPRESS REPRESENTATIONS OR WARRANTIES OF ANY KIND, AND WE MAKE NO REPRESENTATION OR WARRANTY THAT THIS SITE(OR ANY INFORMATION PROVIDED IN RESPONSE TO YOUR INQUIRY), WILL BE ACCURATE, COMPLETE, OR ERROR-FREE. Learn More, 8800 NW 23rd ST Miami, FL 33172, United States. Also, leave the line in a little so you can clean it up with the plane after. Here's how to hang a door - step by step. Scribe this into the side of the door and lining too. When hanging heavy exterior doors, fire check doors, hardwood doors or doors in a bathroom/airing cupboard for example, you should mark a line and position for a third hinge in the center of the door and frame as well. If it fits OK, put the rest of the screws in the hinges. Hopefully the door lining was installed properly (tips on this page for fitting door frames correctly here)and it is square, level and 'in wind'. Is the door edge on the hinge side square or beveled? Loose joint hinges, pivot reinforced, electric, etc. Click here for help applying a leading edgeto the door that helps stop it from binding. The position of the light switch may help - really you want to avoid hanging an internal door so the switch is behind it when opened! Set the marking gauge up as shown in the pictures below and scribe the width of the hinge into the door edge, always working from the face edge of the door and frame. Make sure the screws finish flush. For operating clearance, the hinge backset on the door is 1/16" less (smaller) than the hinge backset on the frame. Third hinge centered between top and bottom hinges.

How do you know which way around to hang a door, and which way up? Hinge backset is the dimension from the leading edge of the hinge to either the stop on the frame or to the stop face (push side) of the door. If you do use a circular saw, score the door with a straight edge and sharp Stanley knife before you cut the bottom off to prevent tear out. Unless I am hanging doors to match existing ones or the schedule says otherwise, I mark a clear line with a sharp pencil on both the lining and the door - 150mm down from the top (this is the top of the top hinge) and 230mm up from the bottom (this is the bottom of the lowest hinge). fraction thereof. Lift the internal door out of the clamp, offer it up to the frame at a slight angle and screw the top hinge to the lining first. Once all the hinge positions are marked, remove the door from the lining, place it in the saddle and wedge it, hinge side up. The first door I hung took me all day to finish! Carefully pare away the waste, keeping inside the lines.

Use two hinges on doors up to 5 (1.52m) and an additional hinge for each additional 2.5 (.76m) or Determined by door size, thickness, weight, frequency of use, and clearance required. In terms of which direction to hang a door, quite often the door can only really open one way and so the decision is easy.

Flat button tip is universally used as standard. If you are fitting loose pin hinges, you may need to take the pin out and slide it back in the other end so it doesnt fall out after you hang the door (below right). Raise the door up in the opening using a wooden wedge until only a 2/3mm gap is left at the top. If the walls are freshly plastered, I use an old blunt chisel to scrape any large lumps of plaster off the door lining and if needed an orbital sander to clean it up further. When I first learned how to hang a door I used to carefully screw the hinge to the door/frame in the exact position and mark all the way round it with a sharp Stanley knife. You can cut a spacer or use cardboard in between to ensure consistency when hanging more than one door. If you are hanging an oak door for example or one that you dont want to risk denting, nail an off-cut of doorstop or other timber temporarily (don't bang the nail in all the way) to the line instead as this is less likely to mark the face of the door. Use the comments box below if you have any questions or tips of your own to add about hanging doors, 5 Things you probably didn't know about Carpentry Pencils, Top 10 Basic Carpentry Skills every newbie should master, was one of the first things I learned to do when I started my carpentry apprenticeship. Put the door in the lining with the lock block in the side where the handle will be fitted. It is important with a flat hollow core door to make sure the lock block will be in the right place before hanging it. Entering your question as a complete sentence will provide more accurate results than keywords or phrases. Other fasteners are available and.

More about dealing with that on this page where I'm hanging an exterior stable door. I always put an x on the side of the line where I want the hinge to be on both the frame and door so I dont chop the hinge in the wrong side of the line (Again!). It is fairly simple to do, as long as you understand the possible problems you can come up against. Someone's got to sand that off later.. probably you. what does door hinge preperation look like for standard weight hinge and heavy weight hinge? For 1 3/4" doors prepared with 4 1/2" or 5" butt hinges (Steelcraft standard hinge backset): For special thickness doors (over 1 3/4" thick): Hinge size must be specified. Primary consideration is given to the type of door and frame for selection of a proper hinge configuration. The right way, (tips on this page for fitting door frames correctly here).

** Certain western states use as standard 7 (178mm) from top and 11 (279mm) from the bottom. are handed and should be specified right or left hand. Hollow core doors have a 'lock block' inside that is a solid piece of timber to secure your latch/lock handles to. It also allows you to put them back where they should be for your new door (or fit nice new ones). You can see above that if you close the hinge so each leaf is parallel, then set the gauge to the same thickness as the hinge the gap between the door and frame is set as per the gap in the picture. I use squares and gauges now though because it's much more accurate and consistent, I know the hinge will be perfectly parallel to the door edge and positioned identically in the lining as well.

Determined by considerations such as atmospheric conditions, location of doors, or special conditions as in, While ferrous metal can be given a good rust-resisting base, it cannot be given the same absolute. Do this about three inches down from the top, and the same up from the floor - out of the way of the hinges. It is usually marked on the top of the door, you can also double check by tapping the door with a knuckle - it will sound hollow on the wrong hinge side and solid on the lock side. Square all the pencil lines across with the combination square. Bottom hinge 10 (254mm) from bottom edge of barrel to finished floor. Old door frames may need the old door stops removed and the frame sanding back a bit while they are off just to clean them up and make the decorators job a bit easier. Sounds like a stupid question but I have seen doors hung upside down on many occassions.. Privacy Policy | About Allegion Allegion plc, 2014 | Block D, Iveagh Court, Harcourt Road, Dublin 2, Co. Dublin, IrelandREGISTERED IN IRELAND WITH LIMITED LIABILITY REGISTERED NUMBER 527370Allegion is an equal oppurtunity and affirmative action employer. I usually allow about 18-20mm for carpet and underlay. If it is an exterior door frame it will most likely already be rebated, you may just need to rebate the bottom of the door over the weather strip. When an exact match of another manufacturers finish is desired, please submit sample. NAAMM/HMMA measures to the edge of the cutout, Frame =5/16" (leading edge of hinge to the frame stop), Door = 1/4" (leading edge of hinge to the stop face of the door), Frame =Backset and Hinge size must be specified, Door = Steelcraft does not supply special thickness doors. Click here if the door needs adjusting in some way. Better to get it right even if slow, you can build up speed as you gain experience hanging doors. click here for help fitting the tubular Mortice latch, handles and doorstops to it. Stanley Hinges has provided an aid to review all considerations before making a final selection. Keep reading to see the steps I go through and in the specific order to get my doors hanging perfectly every time. Then chop in at about 10mm intervals to the depth set by the gauge at a 45 degree angle, as shown in the picture below left. There are a number of factors to consider when selecting a door hinge type and configuration.

Raised barrel, electric hinges, pivot reinforced hinges, hinges with non-removable pins, security studs, etc. * Anti-friction bearings include Lifestan CB bearings and ball bearings. and finally to hold the door in position while I work on it a. I mark sharp clear but faint lines that are easy to sand off later, and only mark where needed - don't put a huge line across the whole width of the door!

More about dealing with that on this page where I'm hanging an exterior stable door. Top hinge 5 (127mm) from frame rabbet to top of barrel. If the frame doesn't have door stops already built into it then set your combination square to the thickness of the doors edge (often 35 or 44mm thick) and then use it to mark a line in from the face of the lining at each corner like the picture below.

If the door needs to be fitted to the frame do so by planing with an electric or hand plane depending on how much needs to be taken off. Sometimes it's necessary to apply a leading edge to the door so it doesn't hit the frame. This will be very easy with a sharp chisel.Sand any remaining pencil lines out, drill correct pilot holes if you need to and once all hinges are recessed screw the leaf side of the hinges to the door (leaf side is that in the picture above, that the marking gauge is set to) with your battery drill. The reference below is intended for end-users so that they may be more familiar with all factors used to determine proper hinge selection. Standard fasteners furnished with each hinge are specified in this catalog. The method or measuring hinge backset varies between SDI and NAAMM/HMMA. Door = Steelcraft does not supply 1 3/8" doors. Once it is hung perfectly click here for help fitting the tubular Mortice latch, handles and doorstops to it.

You can use a Board & Door Lifter to make this easier. If the carpet or flooring isn't already down, check there is a large enough gap underneath to allow for the floor covering and if there isnt mark what you need to cut off now too.

Some old fashion doors have three tall slim panels at the bottom, and one large square panel at the top.

*** The suggested location for olive knuckle and paumelle hinges is 1/4 (6.4mm) from pull side of door to edge of hinge leaf. Institutions often require hospital type tips (barrel ends sloped) making it difficult to attach rope, wearing. Heavy weight hinges should always be used on heavy doors and doors where high frequency is expected. Sometimes the door doesn't always fit perfectly straight away.

The weight of the door and frequency of use determine whether a heavy weight, standard weight. Too deep and the hinge side will 'bind', meaning the door will try and bounce open when you close it! (US Standards Procedure) If you have flat head screws, I finish the screws so the recess for the screwdriver is at a slight angle and all the screws align (OCD). should frames be reinfored for continous hinges, SHOULD FRAMES BE REINFORCED FOR CONTINUOUS HINGES, should frames be reinforced for continuous hinges, what hinges are aproved for hurricane doors, what is standard backset for ND series locfs. Always start by chopping the top and bottom of the hinge horizontally first with a sharp chisel (preferably one that does it in one hit). If you want the gap tighter, set the gauge a little deeper than that and vice versa.

SHOULD FRAMES BE REINFORCED FOR CONTINOUS HINGE. These instructions work for you whether you are trying to hang a door internally, externally, by yourself, in a new frame or in an old door frame as well - the theory is largely the same.

Place the hinge so as to mark the length of it on the doors edge. Repeat for all the hinge positions and then set up another gauge if you have one to the thickness of the hinge (I always use two marking gauges to save set up time when hanging lots of doors).